Jump to content

asalinasl

Members
  • Content Count

    8
  • Joined

  • Last visited

About asalinasl

  • Rank
    Newbie

Profile Information

  • Country
    Germany
  • Are you University user?
    No

Recent Profile Visitors

632 profile views
  1. Hi JIF! this whole post is for me quite helpful and gives practical insight about modelling of wires. My problem is the modelling of flat coils made of litz wire (multistrand wire https://en.wikipedia.org/wiki/Litz_wire.). In my model the litz wire of the coils has a diameter of 5 mm, the biggest coil has 20 turns with a outer diameter of approx. 400 mm and the working frequency is 90kHz. Initially I modelled in FEKO the litz with wires using "metallic_copper" as medium but I received an error regarding the relation "maximum radius to segment length" -after meshing there definitely are some small segments that violate the "thin line approximation". For this problem you suggest to use "real cylinders". First possibilty: I modelled the litz with hollow cylinders i.e. region=free_space and faces=metallic_copper but I have to input a thickness. What is the correct value to be used as thickness? The litzt diameter of 5mm or the litz radius (2.5mm)? Second possibility: to model the litz with solid cylinders i.e. region=dielectric_copper. Because in the model I'm using VEP for other material (ferromagnetic) then I 'd have to use VEP also for the litz wires. Which of the two possibilities is correct for the modelling of litz wires? Looking forward to your reply!
  2. Dear all, I can't start any big simulation in Flux because the programm hangs. And the error message appears: Radflex_2018: cannot open pipes. Please check your Altair License Management System Regards Alfredo
  3. Hallo Tinh, I tried it too, but the same error message came. :wacko:
  4. Hi Tinh! I copied the code that you posted but the problem persists. i.e. I always Need first to open the appearance panel in order to get the axes to disapper. The script works but at the end I always got the following error: ----------------------------------------- can't read "fgc": no such variable can't read "fgc": no such variable while executing "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "ApplyAppearence" line 1) invoked from within "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "ApplyChanges" line 1) invoked from within "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "OnCloseDialog" line 1) invoked from within "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "::post::optionsdialog::OnButtonPressed" line 1) invoked from within "::post::optionsdialog::OnButtonPressed 1" ("after" script) ------------------------------------------------------ Regards Alfredo
  5. Tinh, you are right!! If I firstly open the appearance pannel, then my script including the two added lines works quite well by turning the axes off and afterward again on. The question is how can I automatically open that Panel before I run my script. You wrote about doing that when hyperview was started. Could you give me more Details about that? The best solution would be to add some code in my script to open the apperance Panel automatically in order to get the two lines: ------------------------------------------------- set ::post::optionsdialog::axes false ::post::optionsdialog::OnButtonPressed 1 --------------------------------------------------- working. Thanks for your advice!
  6. Hi, I'm just placing the two lines set ::post::optionsdialog::axes false; ::post::optionsdialog::OnButtonPressed 1; in a bigger script and I'm getting following error: -------------------- 1 Error: Tcl script error (Capture HI Res Image) : can't read "fgc": no such variable while executing "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "ApplyAppearence" line 1) invoked from within "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "ApplyChanges" line 1) invoked from within "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "OnCloseDialog" line 1) invoked from within "# Compiled -- no source code available error "called a copy of a compiled script"" (procedure "::post::optionsdialog::OnButtonPressed" line 1) invoked from within "::post::optionsdialog::OnButtonPressed 1" ------------------------------ Thanks for the help!
  7. Thank you very much! That's exactly what I needed Regards Alfredo
  8. Hi! is there a tcl/tk command in order to hide the Global axes in Hyperview? I need for a scrip ;-) In other words I want to do is to turn off the Global axes like with the Preferences>Options>Appearance Panel, but with a tcl script Thanks
×
×
  • Create New...