Jump to content

Search the Community

Showing results for tags 'RANS'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Altair Support Forum
    • Welcome to Altair Support Forum
    • Installation and Licensing
    • Modeling & Visualisation
    • Solvers & Optimization
    • Multi Body Simulation
    • Conceptual design and Industrial design
    • Model-Based Development
    • Manufacturing Simulation
    • CAE Process Automation
  • Academic Partner Alliance Forum
    • APA - Composites
    • APA - CFD & Thermal
    • APA - Vehicle Dynamics
    • APA - Manufacturing
    • APA - Crash and Safety
    • APA - Noise, Vibration and Harshness
    • APA - System Level Design
    • APA - Structural and Fatigue
    • APA - Marine
    • APA - Optical Design
  • Japanユーザーフォーラム
    • ユーザーフォーラムへようこそ
    • Altair製品の意外な活用例
    • インストールとライセンス
    • モデリング(プリプロセッシング)
    • シミュレーション技術(ソルバー)
    • データ可視化(ポストプロセッシング)
    • モデルベース開発
    • コンセプト設計と工業デザイン
    • 製造シミュレーション
    • CAE プロセスの自動化
    • エンタープライズソリューション
    • データアナリティクス
    • 学生向け無償版

Categories

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Interests


Organization

Found 2 results

  1. General Applications The starting point for most applications should be the steady state Spalart-Allmaras model. For most industrial applications, this model provides sufficient accuracy. For applications involving massive separation, the DES model may be used if a higher level of accuracy is required. Unsteady Simulations For the simulation of unsteady flows, users have the option of unsteady RANS (URANS), DES, or LES. Depending on the goal of the simulation, different turbulence models may be used. If the unsteadiness in the flow is driven by some type of thermal transient, then the use of URANS (i.e. the Spalart-Allmaras model in unsteady mode) is typically sufficient. If the unsteadiness is due to large scale separation and bluff body vortex shedding, the DES model or LES model should be used. For cases where small scale turbulent structure is of interest, the Dynamic LES model should be used.
  2. AcuSolve supports three different techniques of modeling turbulent boundary layers. The first, and most accurate technique is to fully integrate the equations directly up to the no-slip wall. When the user selects "Low Reynolds Number" for the turbulence wall type, AcuSolve uses this procedure to model the boundary layer. When using this technique, it is important that the user constructs the mesh such that the first node off of the wall is within the laminar sublayer (i.e. y+ <= ~8). If the y+ exceeds this value, large errors in the accuracy of the shear stress can be introduced. Note that these guidelines are valid for the DES models and Spalart-Allmaras RANS model. When using LES, the first node off the wall should be at a y+<1.0. The wall normal mesh spacing should increase with a stretch ratio of ~1.3 until it smoothly blends into the surrounding volume mesh. The second type of treatment for turbulent boundary layers is the use of a wall function. When the Turbulence Wall Type is set to wall function, AcuSolve uses the well known "Law of the Wall" to model the boundary layer. When employing this technique, the first node off the wall should be placed between a y+ of 1-300. For extremely high Reynolds Number flows, the upper bound of the y+ limit may be extended beyond 300 without sacrificing accuracy. Note that AcuSolve has no lower limit on the near wall spacing when using the wall function. When in the viscous sublayer, the wall function recovers the Low Reynolds Number solution. This type of wall function can be used with either the DES or RANS models, but is not suggested for use with LES models. The third type of wall model that is offered by AcuSolve is the running average wall function. When this model is employed, the wall function is evaluated using the running average velocity field and not the instantaneous field. The meshing requirements for this model are the same as for the standard wall function. This approach is typically used with LES and DES models, but may also be used with RANS if appropriate. Note that this requires the Running Average field to be turned on in the simulation.
×
×
  • Create New...