Jump to content

Search the Community

Showing results for tags 'linear static'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Altair Support Forum
    • Welcome to Altair Support Forum
    • Installation and Licensing
    • Modeling & Visualisation
    • Solvers & Optimization
    • Multi Body Simulation
    • Conceptual design and Industrial design
    • Model-Based Development
    • Manufacturing Simulation
    • CAE Process Automation
  • Academic Partner Alliance Forum
    • APA - Composites
    • APA - CFD & Thermal
    • APA - Vehicle Dynamics
    • APA - Manufacturing
    • APA - Crash and Safety
    • APA - Noise, Vibration and Harshness
    • APA - System Level Design
    • APA - Structural and Fatigue
    • APA - Marine
    • APA - Optical Design
  • Japanユーザーフォーラム
    • ユーザーフォーラムへようこそ
    • Altair製品の意外な活用例
    • インストール / ライセンス / その他
    • モデリング(プリプロセッシング)
    • シミュレーション技術(ソルバー)
    • データ可視化(ポストプロセッシング)
    • モデルベース開発
    • コンセプト設計と工業デザイン
    • 製造シミュレーション
    • CAE プロセスの自動化
    • エンタープライズソリューション
    • データアナリティクス
    • 学生向け無償版(Altair Student Edition)


There are no results to display.

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 7 results

  1. Guest

    Linear Static Analysis.

    Hi, I have attached a running board linear static analysis. I’m getting a deflection of about 0.0053mm deflection. But in real scenario they are experiencing 1 to 5mm deflection. Instead of applying load on REB3 if I applied load as a point load (single point in the middle of 200 x 80 mm) I’m getting deflection of 3mm. So what should I do here? Should I use REB3 or point load for a cross section of 200 X 80 mm Thanks, Vijay
  2. hm.hmguys, can u help...... how to give self contact for the spring which wouldnt penetrate while doing non-linear analysis...i am hypermesh with opticstrut as slover https://photos.app.goo.gl/9MARHszowpG7fMJ1A
  3. Hello, I am trying to run a linear static analysis which has 36 loadsteps. I need to apply these loadsteps in sequence and need the results from the previous step to be retained for the next step. I am trying to use the statsub(preload) card but it gives an error that subcases cannot be nested. What is the right way to do this in a linear static analysis.
  4. I am carrying out a linear static loading of helical spring, which is interfaced between two plates and have defined slide contact between the spring and the plates. Upon applying the load to the top plate i obtained the spcf forces on the bottom plate nodes. However, I am obtaining unexpectedly high loads at the contacts (100 times higher than the loading force~1000). Am i doing something wrong in setting up the contacts? I am attaching pictures of result, setup and contact surfaces for clarity
  5. How to apply displacement as load in linear static analysis in Optistruct? and apply the same in local co-ordinate system? Rgds, Arul
  6. Hello, I am new to Optistruct and having a repeating error for my 2D linear static topology optimization. When I try to run it w/Optistruct, the error that I get is: *** ERROR # 2148 *** Invalid design problem. All the sensitivities of response 2 (objective) are zero. My response(2) is compliance, and I have a simple maximum constraint on volume fraction as my other response. Any ideas about a possible reason for this error? Thanks, rbay
  7. Hai all, I am doing a linear static analysis by optistruct, when i try to run there show an error "fixed boundary condition in spc is not supported for linear static analysis" what will be the reason for this error? Please help me to understand the error and its solution. best regards, Dani
  • Create New...